| 品牌 | 永成 |
|---|---|
| 型号 | YCYXJ |
一、 机器的用途
The introduction of the machine
泡绵压形机主要用于泡绵凹凸花纹加工， 根据波纹大小， 可分为大波、中波、小波， 适合泡绵家私制造及生活用品加工， 操作方便易学、用途较广。
This machine mainly cuts the foam into concave and convex shape It’s could be divide into large wavemedium wave and small wave according to its wave. And it is suitable for mattress and article for daily use. It’s convenient and easy to learn and has a comprehensive usage.
二、 主要技术规格
Specifications
机械型号 Machine type | BHYX-1500 | BHXY-2000 | BHXY-2400 |
压绵宽度 Foam Width | 1500mm | 2000mm | 2400mm |
切割厚度 Cutting thickness | 20-280mm | ||
切割速度 Cutting speed | 1.5-25mup/min | ||
刀带长度 Blade length | 9000mm | 9700mm | 9700mm |
波峰**大高度 Maximize crest height | 30mm | ||
功率 power | 8.74kw | ||
三、 机器的构造
Constructions of the machine
本机由机架、工作台、压花辊滑座、上下压花辊、刀带涨紧调整部件、刀轮、磨刀部件、外罩等部分组成。
1. 机架主体主要由型材（国际槽钢）焊接组合而成， 两刀轮面需安装定位在同一平面上， 调试好后位置不得变动。
2. 通过上下移动压花辊控制切绵厚度， 海绵随上下压花辊旋转卷进压花，同时并通过高速运转刀带切割海绵， 完成上下两块花纹形状加工。 上下压花辊离刀口距离一样才能保证上下花形状厚度一致。
3. 用本公司所配“Ｆ”型扳手， 左右旋转右下方涨紧手轮可涨紧或松开刀带。关掉电源待刀轮和刀带完全停止运转方可拆换刀带， 换刀带时应戴手套以防割伤手。
4. 刀带上下两边各有磨刀砂轮一个， 砂轮端面与刀带大致成15°角， 砂轮由120Ｗ电机带动， 中等密度海绵一般每10分钟磨刀一次， 具体磨刀时间依海绵密度大小有所不同。
5. 刀带刀口一般露出刀盒3mm， 刀口露出多少可由刀盒上的顶刀片进行前后调整
6. 旋转工作台下面手轮可调整工作台上下高度， 调好工作台后应锁紧两边圆齿条上螺栓以防上下滑动。
This machine consisted with machine-frameworktable、slide carriage of knurl rollhe top and bottom knurl rollension adjustment parts of bladeblade wheel grinding device and outer cover.
1. The machine-frame is jointed by the international channel steel. The two blade wheel should be installed in the same plane. The situation should not be change after debugged.
2. Adjust the cutting thickness by moving the knurl roll up and down. The foam will be press into concave and convex along with the top and bottom knurl roll. Meanwhile, the foam will be cut by the running blade in high speed. So the process for two patterned foam were completed. only if the distance between blade and the top and bottom knurl roll is the same, will the thickness of the foams which have been cut are the same.
3. We offer you a detent of F shape. Turn the bottom-right tension wheel to lift and right and the blade will be tighten and loosen. only if the power was turn off and the wheel and the blade was completely stopped could you dismantle or change the blade. Please wear gloves when changing blade to avoid being cut.
4. There is a blade grinder in both side of the blade. The angle between blade grinder and the blade is about 15°.The motor power of blade grinder is 120W. Grind the blade 10 minutes a time for the foam in medium thickness. And the exact grinding time is vary from the thickness of the cutting foam.
5. There shall be3mmedge bare from the blade clamp.